HEAVY-DUTY COMMERCIAL GAS WATER HEATER SPARK
IGNITION
- 1-Year Limited Warranty** on Tank
Heavy-gauge steel is automatically formed,
rolled and welded to assure a continuous
seam for glass lining. Each tank is double
tested to ensure quality.
- 1-Year Limited Warranty** on Parts
- 1" of Polyurethane Foam - Non-CFC
Foam insulation saves fuel by retarding heat
loss.
- Fused Ceramic ShieldTM
Applied under pressure and field at 1600oF
to completely cover the tank interior. This
provides a tough interior surface for
storage tanks and maximum protection against
the wearing effects of high-volume and
high-temperature hot water.
- Self-Cleaning LimeFighterTM
Reduces scale and corrosive deposits that
are detrimental to the life cycle of
commercial water heaters.
- 24-Volt Thermostat Control
Adjustable to temperatures up to 180oF.
A recycling energy cut-off (ECO) control
shuts off gas in the event of an overheat
condition.
- Power Cord
Supplied and wired for easy installation and
service or can be hard wired.
- Electronic Thermister Sensor
For consistent water temperature control.
- Multiple Anode Rods
Promote longer tank life through even
distribution, for protection against
corrosion of tank interior.
- Factory-Installed Temperature and
Pressure Relief Valve
- Electronic Intermittent Spark Ignition
Eliminates standing pilot light for maximum
energy efficiency.
- Motorized Flue Damper
Reduces tank heat loss during standby
periods for lowest operating costs.
- Recoveries
First-hour delivery ratings are based on
thermal efficiencies ranging up to 80%.
Recovery figures shown on water heater
rating plates are based on 75% thermal
efficiency in compliance with (AGA) ANSI
Z-21.10.3 requirements.
- Design Certified
By the American Gas Association and Canadian
Association for up to 180oF, as
an automatic storage heater in compliance
with AGA ANSI Z-21.10.3 test requirements.
- ASHRAE Standard 90.1 1989 addendum 90.1
b.
Thermal efficiency and standby loss
requirements are met or exceeded.
- California (CEC) and New York
Energy requirements met or exceeded.
- Builder Block Concept
Enables multiple heaters od equal size and
input manifolded together to operate as one
total system. This concept allows the system
to be maintained and serviced without
shutting down the complete system.
** Limited warranty on tank and parts.
Complete details in manual.
Dimensions in all charts shown
in inches.
All recovery rates based on 100oF
rise.
*ASME Models. Limited warranty on tank and
parts. Complete details in manual. To order
propane models, change suffix from "N" to "P".
No Top Connections.
SPECIFICATION
Furnish and install, where indicated, in
accordance with manufacturer's instructions and
in compliance with all rules and regulations of
authorities having jurisdiction.
Commercial gas-fired water heater(s) shall be
American® Model ________________ as manufactured
by American Water Heater Company, designed to
burn ________________ gas and certified by the
American Gas Association (AGA) under Volume III
tests for commercial water heater(s) having
delivery capabilities of 180oF water,
and meet or exceed all applicable energy codes.
Water heater(s) shall have a storage capacity of
_______ gallons, a minimum input rating of
________ Btuh and recovery rating of ________
GPH (based upon 80% thermal efficiencies) at a
______oF temperature rise. Water
heater(s) steel tank is hydrostatic tested at
300 PSI having a working pressure of 150 PSI and
shall have a Fused Ceramic ShieldTM
internally lined tank applied under pressure and
fired at 1600oF allowing for maximum
protection. Water heater(s) shall be equippe
with a full-sized 4" dia. boiler type inspection
port/cleanout. Water heater(s) shall be provided
with a recycling enegy cut-off (ECO) device, gas
pressure regulator set for the type of gas
supplied, IID electronic ignition, agency
approved flue damper and draft diverter, and
anodes for cathodic protection. The outer
jacketing shall have a backed enamel finish. The
tank shall be foam insulated with an
EPA-approved, non-CFC material. Water heater(s)
shall be manufactured in United States of
America and shall have a 1-year limited tank
warranty against corrosion as outlined in the
written warranty. Fully illustrated operation,
installation and service manual included with
unit.
ADDITIONAL SPECIFICATIONS FOR ASME CODED
COMMERCIAL WATER HEATER(S)
Commercial gas-fired water heater(s) shall be
American® Model ________________ as manufactured
by American Water Heater Company, having an
input of 200,000 Btuh or greater, shall be ASME
certified, and stamped National Board labeling
permanently affixed to the tank and accessible
for inspection. |
